Modeling of stall cavitation sensitivity of a booster turbopump assembly and comparison between experimental and numerical results
- Authors: Kazyonnov I.S.1, Kanalin U.I.1, Poletaev N.P.1, Chernisheva I.A.1
-
Affiliations:
- Energomash Science and Production Association named after academician V.P. Glushko
- Issue: Vol 13, No 5-1 (2014): Special Issue
- Pages: 188-198
- Section: ISSUE WITHOUT SECTION
- URL: https://journals.ssau.ru/vestnik/article/view/2497
- DOI: https://doi.org/10.18287/1998-6629-2014-0-5-1(47)-188-198
- ID: 2497
Cite item
Full Text
Abstract
Nowadays, screw booster pumps (BP) are used in engines of large and small thrust both of Russian and foreign designs to reduce the pressure in the tanks. Cavitation may occur in BPs like in any hydraulic systems. To determine the cavitation characteristics of screw and centrifugal pumps a number of empirical formulas were obtained which do not fully take into account all the geometrical features of variable-step screws. Various models of cavitation are used in CFD programs; cavitation properties of any geometry can be obtained on the basis of these models. The paper presents the results of numerical analysis of the cavitating flow in a booster pump and their comparison with the experimental ones. Modeling was performed by ANSYS CFX. The cavitation phenomena were simulated in a stationary approach using the Rayleigh-Plesset model. The geometrical model included an axial-radial wheel and straightening vanes. The analysis was performed with and without a shroud ring, a clearance gap and roughness. On this basis, a method of calculating the stall cavitation characteristics is developed using ANSYS CFX.
About the authors
I. S. Kazyonnov
Energomash Science and Production Association named after academician V.P. Glushko
Author for correspondence.
Email: kazyonnov.ivan@gmail.com
Programmer engineer
Russian FederationU. I. Kanalin
Energomash Science and Production Association named after academician V.P. Glushko
Email: otd769@mail.ru
Chief Specialist
Russian FederationN. P. Poletaev
Energomash Science and Production Association named after academician V.P. Glushko
Email: otd769@mail.ru
Leading Design Engineer
Russian FederationI. A. Chernisheva
Energomash Science and Production Association named after academician V.P. Glushko
Email: otd769@mail.ru
Head of Sector
Russian FederationReferences
- Borovskij B.I., Ershov N.S., Ovsyannikov B.V., Petrov V.I., Chebaevskij B.F., Shapiro A.S. Vysokooborotnye lopatochnye nasosy [High-speed vane pumps]. Moscow: Mashinostroyeniye Publ., 1975. 336 p.
- Ovsyannikov B.V., Borovskij B.I. Teoriya i raschet agregatov pitaniya ZhRD [Theory and calculation of power supply units of liquid rocket engines]. Moscow: Mashinostroyeniye Publ., 1971. 376 p.
- Valueva O.A., Vidishev V.I., Kanalin U.I., Poletaev N.P. Cavitation characteristics of screw boost pumps of LPRE of NPO Energomash design // Trudy NPO Energomash. 2005. No. 23. Р. 306-320. (In Russ)
- ANSYS CFX-Solver Theory Guide. ANSYS CFX Release 11.0. © 1996-2006 ANSYS Europe, Ltd.
- Bakir F., Rey R., Gerber A.G., Belamri T., Hutchinson B. Numerical and experimental investigations of the cavitating behavior of an inducer // Int. Journal Rotating Machinery. 2004. V. 10. doi: 10.1155/s1023621x04000028
- Philippe Dupont, Tomoyoshi Okamura. Cavitating Flow Calculations in Industry // International Journal of Rotating Machinery. 2003. doi: 10.1155/s1023621x03000150
- Youcef AIT BOUZIAD. Physical modelling of leading edge cavitation: computational methodologies and application to hydraulic machinery. EPFL - Laboratoire de Machines Hydrauliques, 2006.
- D Pierrat, L. Gros, A. Couzinet, G. Pintrand, Ph. Gyomlai. On the Leading Edge Cavitation In a Helico-centifugal pump: Experimental and Numerical Investigations. IAHR WG Meeting on Cavitation and Dynamic Problems in Hydraulic Machinery and Systems, 2009.
- Hou-linLIU, Dong-xi LIU, Yong WANG, Xian-fang WU, Jian WANG. Application of modified k-ω model to predicting cavitating flow in centrifugal pump // Water Science and Engineering. 2013. V. 6, no. 3. P. 331-339. doi: 10.3882/j.issn.1674-2370.2013.03.009
- Rafael Campos-Amezcua, Sofiane Khelladi, Zdzislaw Mazur-Czerwiec, Farid Bakir, Alfonso Campos-Amezcua, Robert Rey, Numerical and Experimental Study of Mass Transfer Through Cavitation in Turbomachinery. InTech, July 2011.
- Jose J.K., Mmbaga J.P., Hayes R.E., Xu Z. Modeling Cavitation in a High Intensity Agitation Cell // Canadian Journal of Chemical Engineering. 2011. V. 89, no. 5. P. 1154-1164. doi: 10.1002/cjce.20612
- Popov E.N. Modeling of a threedimensional flow of liquid in an oxygen pump of a liquid rocket engine considering cavitation // Trudy NPO Energomash. 2010. No. 27. P. 65-94. (In Russ)
- Johann Friedrich Gülich. Centrifugal Pumps (second edition). Springer Heidelberg Dordrecht London New York, 2010.
- Miorini R. L., Wu H. Katz J. The Internal structure of the tip leakage vortex within the rotor of an axial waterjet pump // J. Turbomachinery. 2011. V. 134, no. 3. Article number 031018. doi: 10.1115/1.4003065
- Wu H., Miorini R. L., Katz J. Measurements of the Tip Leakage Vortex Structures and Turbulence in the meridional plane of an axial Water-Jet Pump // Experiments in Fluids. 2011. V. 50, no. 4. P. 989-1003. doi: 10.1007/s00348-010-0975-0