Vol 11, No 3-1 (2012): Special Issue

Cover Page

Full Issue

Pressure pulsation dampener for air controller

Igolkin A.A., Safin A.I., Shakhmatov E.V.

Abstract

The article deal with pressure pulsation dampener (PPD) which reduce noise emitted by the valve. The results of numerical simulation and experimental study of the PPD. As a result of the work and tests, the efficiency of the pressure pulsation dampener was 10,6 dBA.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):11-16
pages 11-16 views

Problems fatigue (HCF) of constructional materials and detals GTE

Petukhov A.N.

Abstract

At formation of preparations of details of the difficult form, different zones of preparations essentially differ on degree of deformation of a material (for example, a nave, a cloth and a disk rim), that is reflected and in properties CHF. Check of properties of a material realised in a detail is spent for the most critical zones of a detail where are shown influence consequences on a detail of operations of the raised risk and the maximum operational loadings operate.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):17-25
pages 17-25 views

Methods of increase of wear resistance and vibroakusticheskikh of parameters of knots of the friction of space equipment

Gromakovsky D.G., Kovshov A.G., Kotcherov E.P., Makaryants M.V.

Abstract

The ways providing simultaneous increase of wear resistance, decrease in noise level and the vibration generated in knots of a friction are considered. The offered technologies are connected with formation containing fluorine the microdimensional films raising wear resistance, contact weariness and durability of connection of a lubricant layer with friction surfaces; the microreinforcing of superficial defects which is slowing down development of fatigue damages; the effect of multigreasing raising loading characteristics of a lubricant layer and its absorbing ability.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):26-32
pages 26-32 views

About some directions in development avation engine buildings

Zamtfort B.S.

Abstract

Analysis of the acoustic characteristics of the engines with open rotor and turbofan engines shown what in engine noise with open rotor in addition to traditional component of the noise added tonal noise peaks at combination frequencies in low frequency part spectra. All of this creates many difficulties in the reduction the noise of aircrafts with this engines on the ground. Problem of choise engines for future aviation discussed.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):33-38
pages 33-38 views

Optimization methods pilotage aircraft in take-off and approach cycle for decrease square his sound track

Zamtfort B.S., Medvedev Y.V.

Abstract

The evaluation of the noise exposed area during the landing and take-off cycle is performed. The calculations based on two different methods provide satisfactory results and show the decrease in the noise exposed area with the implementation of the alternative piloting techniques for approach operations. In some take-off cases application of the alternative piloting techniques does not result in decrease of the noise exposed area.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):39-43
pages 39-43 views

Management of properties of heat-shielding plasma coverings of details of gas-turbine engines

Barvinok V.A., Bogdanovich V.I., Dokukina I.A., Karasyov V.M.

Abstract

The results of the research methods for thermal barrier coatings with a given structure. The influence of the structure of thermal barrier coatings on their properties and identify ways to improve their performance.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):44-51
pages 44-51 views

Influence of methods of strengthening technology on the stressstrain state and relaxation of residual stresses in titanium alloys

Papsheva N.D., Akushskaya O.M.

Abstract

The results of studies of the effect of ultrasonic hardening of relaxation of residual stresses and strain hardening in titanium alloys. Shows the influence of processing parameters on the intensity of the stresses and strains.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):52-56
pages 52-56 views

The speed function of intensity of one-dimensional moving wave and it’s analysis for shock and compression waves

Arkhipova L.P.

Abstract

In this report the speed functions of one-dimensional moving waves were investigated. Using this variables one can get one universal solution for the problem of finding the speed of the gas after the mooving wave. Also we have got a universal solution for of reflection of one-dimensional moving shock waves. Rarefaction and compression Riemann waves from a solid wall.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):57-62
pages 57-62 views

Obstacles of on-board mathematical models application in ACS

Gayday M.S., Dobrodeev A.V., Muhammedov N.A., Chervonyuk V.V.

Abstract

In this article are considered reasons limiting applicability of model-based adaptive control. Also it’s offered way of the adjustment to linear model in operation with changing of engine’s conditions.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):63-70
pages 63-70 views

Investigation of the possibility of the creation LREST by thrust 400 N with a baffle - centrifugal scheme of NT and NDMG mixing

Ageenko Y.I., Ilin I.V., Pegin I.V., Shalamov E.A.

Abstract

Investigation of the possibility of the creation LREST by thrust 400 N is organized. Broughted analysis of the scheme and results cool working and fire functioning the pilot model of the engine.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):71-76
pages 71-76 views

End mill design and manufacturing with modern multi-axis grinding machines

Skuratov D.L., Kuznetsov A.V., Oparin V.M., Sazonov M.B.

Abstract

Bull nose end mill design is represented. A method to create a control program for end mill fabrication using special software, supplied with ВЗ-30Ф4 grinding machine is described.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):77-86
pages 77-86 views

Reduction of circumferential variation in the final stage of IPC

Popov G.M., Mamedov A.C., Smirnova Y.D.

Abstract

Circumferential variation of the flow in final stage rotor wheel, caused by the support racks at the exit of the IPC, is evaluated by means of intermediate pressure of compressor of workflow 3D model. The methods of reducing the circumferential variation of flow by changing final stage’s guide vanes angles.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):87-92
pages 87-92 views

Numerical investigation of phisical processes in cooling jacket of thrust chamber of LOx – LH2 LRE using 3D computer simulation methods

Yakub P.A., Gumennyy A.V.

Abstract

The problem solution of conjugate heat transfer in thrust chamber cooling jacket of liquid rocket engine is considered. Finding design data is compared with experiment.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):93-98
pages 93-98 views

Design solutions to provide thermal protection of three-shaft turbofan engine turbine support oil cavities

Petrukhin A.G., Boev A.A., Butylkin S.V.

Abstract

The paper presents design approach to providing thermal protection of three-shaft turbofan engine turbine support oil cavities. The advantages and disadvantages of three-shaft engines are described. Basing upon the performed analysis, there are offered the potential decisions for providing thermal protection of turbine support oil cavities.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):99-104
pages 99-104 views

The new testung method of coatings on high-temperature alloys

Tikhomirova E.A., Sidokhin E.F.

Abstract

The method and the instrument are used for thermo-cyclical testing of nickel-base superalloy coatings.
VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):105-108
pages 105-108 views

Optimization of casing on mass with ensuring requirements for deduction of the ragged blade

Krundaeva A.N., Gabov D.V., Maralev A.Y.

Abstract

To automate the search for optimal weight and meet requirements for containment ability of case was established software package based on the program LS-DYNA with the IOSO, which allows by changing the geometry of the receiving case, satisfying for containment ability and low mass.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):109-114
pages 109-114 views

Linear mathematical model for the determination of rational treatment conditions on the diamond smoothing operations in the manufacture of aircraft parts

Skuratov D.L., Shvetsov A.N., Abulkhanov S.R.

Abstract

The mathematical model is submitted for definition of rational conditions of processing at the diamond smoothing, consisting of linear objective function and linear restrictions – inequalities. As objective function the equation determining machine time of processing is used, and as restrictions – inequalities, the restrictions connected in functional parameters and parameters, determining quality of processing.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):115-121
pages 115-121 views

Instrument to measure material resistance to thermo-mechanical fatigue

Tikhomirova E.A., Azizov T.N., Sidokhin E.F.

Abstract

The instrument is used for material thermo-cyclical testing.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):122-126
pages 122-126 views

Investigation of fluid flow in the gap between eccentric cylindrical and conical surfaces

Bondareva M.V., Korzhov E.N.

Abstract

Performed a computer experiment for the flow of an incompressible viscous fluid under a constant pressure drop in an annular channel formed by the cylindrical and conical surfaces between the axes of which there is eccentricity. Based on the results established certain regularities and characteristics of the turbulent flow, and obtained an engineering formula to calculate the coefficient of hydraulic resistance.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):127-134
pages 127-134 views

Calculation methodology of intermittent burning chamber main parameters

Solodovnikov A.V., Vishegorodcev E.N., Golubyatnik V.V.

Abstract

Calculation methodology of direct-flow intermittent burning chamber main parameters (V = const) is treated in this paper. The calculation algorithm is given.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):135-144
pages 135-144 views

Robust research of the fuzzy logic controllers using a fuel flow control loop of the gas-turbine engine as an example

Chicherova E.V.

Abstract

The article issues of application fuzzy logic controllers for the automatic control electronic systems gas-turbine engine is research. A comparative analysis of transient performances a fuel flow control loop with fuzzy logic P controller and line PID controller for the deterministic line system, system contenting dead zone and deflections of parameters invariable part of system comparative them nominal value has been made. As a result of the comparison the best controller has been chosen. Conclusion about of appropriateness using fuzzy logic controllers for the automatic control systems gas-turbine engine has been made.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):145-152
pages 145-152 views

Research of influence of methods SPD on stpucture surface layer and resistance of fatigue

Volkov A.N., Sazonov M.B., Schigrinyev I.A.

Abstract

Methods of combining surface-plasto deformation pieces from titanium alIoy ВТ9. Research of quality of surface layer is fulfilled. Functional dependence is determined between hardiness limit, fine crystalline structure parameters and intensity of exoelectronic emission.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):153-156
pages 153-156 views

The equipment for research of properties of hydrocarbons at pressure from above 150 MPа

Rednikov S.N.

Abstract

Creation of viscometers has been considered for observation and identification of parameters of non-Newtonian fluids. In the paper, problems of measurement of viscosity and changes of temperature of hydrocarbons under the pressure of more than 150 MPa are considered.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):157-161
pages 157-161 views

Increase treatment high strength steels 30HGSN2FA based on a minimum of energy consumption

Trusov V.N., Zakonov O.I., Shikin V.V.

Abstract

The research process of milling the steel. Influence of method milling on the cutting force. Effect of changes in the parameters of the cutting conditions on cutting force. The influence of the cutting on the roughness of the surface. The influence of the cutting on the specific energy consumption.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):162-166
pages 162-166 views

Selection of the design and application of plasma technology protective coatings parts gas turbine engines

Dokukina I.A.

Abstract

The basic methodological principles for the design of plasma technology for protective coatings gas-turbine engines. The parameters of the control system and the technological properties of the coatings.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):167-172
pages 167-172 views

Research of rotor dynamic of GTE with nonlinear stiffness of elastic elements in support parts

Leontyev M.K., Tereshko A.G.

Abstract

The problem of determination of elastic elements stiffness mounted in rotor supports is considered. Analysis results show that elastic elements have characteristics which are depended on working regime.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):173-180
pages 173-180 views

Anode dissolution of a nickel-chromium alloy ЖС6У in various electrolytes

Sayapova V.V., Amirchanova N.A., Ustyuzhanina S.V., Gordeyev V.Y.

Abstract

The surface films element structure after ECDM of the alloy ЖС6У was investigated by an X-ray method. It is established that film properties at electrochemical dimensional machining of a heat resisting alloy ЖС6У in various electrolytes are defined generally by nickel and cobalt component, as their influence in a film is solving.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):181-186
pages 181-186 views

Comparative evaluation of the effectiveness of the application of perspective types of electric propulsion thrusters in the small spacecraft

Kulkov V.M., Obukhov V.A., Yegorov Y.G., Belik A.A., Krainov A.M.

Abstract

The report includes comparative analysis of efficiency in the use of small spacecraft with electric propulsion based on ion thrusters, stationary plasma thrusters and pulsed plasma thrusters.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):187-195
pages 187-195 views

The defectoscopy of the fatigue cracks in the gas turbine parts by means of eddy-current method

Porter A.M., Bukatyi S.A., Leshin D.P., Vasilchuk M.V., Galickyi A.A.

Abstract

The results of research in the sphere of enhancement of efficiency and reliability of the eddy current testing and determination of the minimal size of the revealed fatigue cracks are presented here. The most essential factors influencing on the detectability of the fatigue crack are researched. The methods and technology of the reliable defectoscopy are developed by means of defectoscope D-5.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):196-202
pages 196-202 views

Evolution of structure and mechanical properties in the single-crystal alloys alloyed by Re аnd Ru, after high-temperature excerpts

Kuznetsov V.P., Lesnikov V.P., Konakova I.P., Popov N.A.

Abstract

Changes thin (γ +γ´) structures of single-crystal nickel alloys ZhS36-VI, VZhM4-VI, VZhM5-VI and residual prochnostny properties of these alloys after excerpts in the range of temperatures 1050 … 1300°С are investigated.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):203-210
pages 203-210 views

Design of integrated protective coatings for single-crystal turbine blades modern cooled GTE

Lesnikov V.P., Kuznetsov V.P., Konakova I.P., Moroz E.V.

Abstract

The structure, phase composition and strength of long-term high-resource complex protective coatings for heat-cooled turbine blades from single-crystal nickel-base alloys.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):211-216
pages 211-216 views

Formation of the sliding surface mechanical seal different methods

Tarelnik V.B., Martsinkovskiy V.S., Antoshevskiy B.

Abstract

The problem of improving the quality of the surface layers of detail in the face-end sliding. The results of qualitative and quantitative analysis of surface layers of steel 38H2MYUA formed by various methods.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):217-225
pages 217-225 views

Interaction of exhaust jets of rocker propulsions on various propellants with atmosphere for estimation of ecological safety of firing of rockets and launchers

Zavelevich F.S., Ushakov N.N.

Abstract

The method of calculation of interaction of exhaust jets of RP on various propellants with atmosphere for estimation of ecological safety of firing of rockets and launchers is developed. The model considers non-equilibrium physical and chemical processes, including reactions with ozone, nitrogen-containing and chlorine-containing components, wave processes, process of turbulent mixing, interaction between particles of the condensed phase and gas. The method of calculation is approved on example of influence on ozone cloud of jets atmosphere of SRM LV «Space Shuttle» and LV «Titan» and LRE LV "Proton" (fuel NTO-UDMH) and LV "Angara" (fuel kerosene-oxygen).

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):226-234
pages 226-234 views

EDM laser alloying and texturing the sliding surface mechanical seals

Antoshevskiy B., Tarelnik V.B., Martsinkovskiy V.S.

Abstract

The results of texturing the metal surface by laser and electrical discharge method. The prospects of their use in non-contact face seal type.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):235-240
pages 235-240 views

On plasma support of fuel burning in a combustion chamber of a gas-turbine facility

Bulaeva M.N., Kravchenko I.V., Riaby V.A., Tkachenko D.P.

Abstract

Two models of high-durability DC arc plasmatron that has been used for fuel-air mixture reformation aiming at plasma support of fuel burning in an internal combustion engines were investigated.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):241-246
pages 241-246 views

Effect of the new aircraft types on the environmental situation

Kopiev V.F., Munin A.G., Medvedev Y.V.

Abstract

The aircraft centered environmental model for calculation of the pollutant emission and noise impact is considered. The methods applied allow evaluating the environmental parameters for modern aircraft types as well as for those being under development. As the example a number of calculation results with the corresponding analysis is presented.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):247-252
pages 247-252 views

Development liquid roket engine on component fuel liquefied natural gas and oxygen for reusable space launching systems

Efimochkin A.F., Khrisanfov S.P., Golubyatnik V.V., Kafarena P.V., Yeliseyev A.V.

Abstract

Some problems to create a liquid rocket engine reusability of oxygen in fuel - liquefied natural gas, which uses the shaft turbopump unit two turbines, one of which runs on gas with an excess of oxygen, and the second - on the gasified fuel in the cooling path. Made an experimental model, conducted fire tests and obtained its main characteristics.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):253-258
pages 253-258 views

Improving the processing accuracy of spherical ends of bearing tapered rollers

Nosov N.V., Mikhailova L.N.

Abstract

The error in sphere forming of tapered rollers end in continuous grinding periphery of the circle, filled to the radius, was examined. The analysis of all existing grinding ways by this method was made. The results of researches related to improve the tapered rollers ends sphere accuracy with the corrected radius of processing and device for grinding of spherical ends of tapered rollers.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):259-264
pages 259-264 views

The use of gas turbines in small-scale installations of synthetic fuels

Filipchenko S.A., Faridonov R.R., Gushchina T.V.

Abstract

We offer the production of synthesis gas by means of power saturated technology of a steam and carbon dioxide reforming with use of an exhaust of gas turbines and as use of screw multiphase pumps for Slarri-process on iron catalysts, which possess big advantages.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):265-269
pages 265-269 views

The limits ofdistributionin aflamealuminum-air mixture

Tizilov A.S., Egorov A.G.

Abstract

The region ofstable combustionof aluminum powderASDin high speedair flow. The dependence of thestall speedof the flamein the flow ofaluminum-air mixture in therange of α = 0,04 ÷ 3,0.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):270-274
pages 270-274 views

Research of influence the processes to afterhardening glass transition temperature of PKM

Postnov V.I., Burhan O.L., Rahmatullin A.E., Mantusova O.Y., Nikitin E.K.

Abstract

The results of investigations of the influence of on afterhardening the temperature glass transition PKM

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):275-280
pages 275-280 views

Research vibrational fatigue properties of forward wings bay MPKM

Postnov V.I., Postnova M.V., Mantusova O.Y.

Abstract

The results of static and acoustic investigations of aircraft structures made of metal-grade materials Alor D16/41 and their comparison with serial structures of aluminum alloy.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):281-290
pages 281-290 views

Nondestructive testing of the working compressor blades of the aviation engine

Nikitina N.E., Motova E.A., Tarasenko Y.P.

Abstract

The results of nondestructive testing of blades of axial compressor of aviation engine of gas-pumping unit are represented. The experimental investigations were based on ultrasonic pulse-echo method. The opportunities of the nondestructive acoustical method for the studying of the steel structure during the exploitation of blades are demonstrated.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):291-295
pages 291-295 views

Technological features of formation of the multifunctional nanostructured coverings of nitride of the titan for compressor shovels aviation GTD

Tarasenko Y.P., Tsareva I.N., Kocherov E.P., Vyazovskaya L.M.

Abstract

Results of scientific researches on studying of regularities of formation of the stolbchaty nanostructured coverings of nitride of the titan, intended for protection of a surface of working shovels of the axial compressor of gas-turbine engines of a series NK. Experiments are carried out at a variation of parameters of process of an ion-plasma dusting taking into account.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):296-302
pages 296-302 views

Study of seals influence to supercritical rotor characteristic

Ivanov A.V.

Abstract

This article dedicated to some questions of seals to rotor dynamical characteristics.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):303-308
pages 303-308 views

Modeling flow in a ring body work o-gap-state rocket engine turbopump

Ivanov A.V., Moskvichev A.V., Tsiganov A.A.

Abstract

This article describes the process of modeling the flow of the working body in the annular gap formed by the turbine rotor and the stator turbopump unit, using the Ansys package and the results of the first stage of the calculation.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):309-313
pages 309-313 views

Investigation of structural damping of turbomashine blade vibrations using dynamic spin rigs

Nozhnitskiy Y.A., Fedina Y.A., Shadrin D.V.

Abstract

Consideration is being given to the possibility of using dynamic spin rigs for investigation of turbomachine blade vibrations damping and optimization of structural damping. Investigation results of vibrations damping are presented for turbine and compressor blisk blades and turbine wheel with inserted blades.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):314-320
pages 314-320 views

The automated control system of form of nonrigid shafts in lathing

Nabilkin A.U., Kravchenko S.A., Birukov V.P.

Abstract

The system of automatic control of nonrigid shafts form in longitudinal section in lathing offered in the article. The system is intended for compensation workpiece's deformation in lathing and compensation shifting motions of a head stock and a poppet by reason of limited rigidity, and also low-frequency uncontrollable perturbation actions in instability of rigidity of a head stock and a poppet, basing of a workpiece, wear of a cutting tool by correction of position of a cutting tool in Y-dimension.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):321-329
pages 321-329 views

The analysis of real thermodynamic cycle of bypass engine with mixing

Medvedev V.V.

Abstract

Some theoretical questions and thermodynamic cycle of bypass engines with mixing are analyzed in the article. The formula for optimum cycle parameters providing the maximum efficiency are derived and some comments are presented. The computer investigation with the new formula using is performed. The main results of computer investigation are analyzed and presented.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):330-338
pages 330-338 views

Improvement of efficienсy of the automated control system of nonrigid shafts surface contour in lathing

Kravchenko S.A., Nabilkin A.U., Birukov V.P.

Abstract

The problem of the automated control system of nonrigid shafts surface contour in lathing efficiency improvement is disclosed in the paper. It is shown, that random component of working error of white noise type can be the result of the influence of cutting force change correlated random process. The synthesis of the multidimensional system of cutting force stabilization and cutting tool position along the transverse axis control under the relatedness of these parameters through the control object is produced, and its efficiency is shown with a computer simulation.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):339-348
pages 339-348 views

To the question of cooling power components of radio-electronic equipment by impinging freon jets

Lopatin A.A., Gortyshov Y.F.

Abstract

In this article the short review of the problem of cooling high-power electronic components by impinging jets at various initial conditions is presented. Experiments of researching the heat emission for boiling R-134a on microribbed and microroughed surfaces at the conditions of stationary heating are made. Graphics of dependences of density of the heat flux on distance between the channel and the effective surface are presented. Influence of the form of the channel on the temperature profile is positioned.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):349-358
pages 349-358 views

Numerical modeling on dynamic process of injection in supersonic part of the nozzle

Yakovchuk M.S.

Abstract

The object of the study is the dynamic process of the impulsed jet injection into a supersonic flow in relation to the creation of control efforts. Basing on data from field experiment the study validates turbulence models and grid convergence.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):359-367
pages 359-367 views

Theoretical basis of forming forging impellers of blade machines in multichannel stamps

Vorobjev V.M.

Abstract

It is proposed the classifier of solid stamped impellers used in gas and hydraulic impeller machines produced by hoy (semi-hot) stamping, which were produced in aviation industry. Article recounts information about research and development of schemes and structures of the multisectional stamps, non-dismountable (tyre supported) and dismountable wheels after forming. Extruding insertions are being pulled from interblade channels. It is considered the principle of constructing theoretical cylindrical lattices of channels for multi-split stamps, due to which it is possible to calculate the forces of disclosure in stamps’ channels and rotational forces of the compound matrixes during extrusion.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):368-376
pages 368-376 views

Authenticity of the vibration tests. Diagnosis and prediction of fatigue failure

Ovchinnikov I.N., Ermishkin V.A.

Abstract

The issues compiling numerical computational model on the method of finite volumes are discussed in this paper. This model is used to measure axial acting on the rotor of auger-centrifugal stage of combined fuel pump. Model verified by comparing the calculated and experimental characteristics of the discharge. The paper discusses the impact of some design parameters auger-centrifugal stage on the value of the axial force.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):377-384
pages 377-384 views

Test verification of flow stabilizer calculated parameters provided flow stabilization of propellant in wide range of input parameters

Beshenev Y.A., Volkov A.V., Kazankin F.A.

Abstract

This paper presents a flow stabilizer configuration intended for maintaining regular rated propellants flow through a thruster and also reducing time of transition to steady state mode for any thruster firing in wide range of output parameters.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):385-389
pages 385-389 views

Influence of high technologies on production technological prototypes of missile engines

Kodencev S.N., Suhochev G.A.

Abstract

Provides a basic description of the developer of progressive design and technological solutions.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(3-1):390-396
pages 390-396 views

This website uses cookies

You consent to our cookies if you continue to use our website.

About Cookies