Vol 8, No 3-2 (2009): Special Issue

Cover Page

Full Issue

AIRCRAFT AND SPACE ROCKET ENGINEERING

Electronic model of turbine drive flow for its direct optimization

1 1.

Abstract

Work has described in theses is dedicated to problem of creating finite-element models of high-quality for gasdynamic research. Is offered model composed like a combination of separated parts-modules connected together in preprocessor Ansys CFX-Pre. Model has opportunity to include modules created in purely arbitrary 3D-modeling and meshing systems. Even so it keeps correctness what was shown by test-computing. Model processes flexibility and versatility and can be applied for analysis of turbomachines and similar-topology devices.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):11-16
pages 11-16 views

Design improvement of multi-film rotor journal bearings of diesel engine turbochargers

1 1., 1 1.

Abstract

Three developed models of diesel engine turbocharger rotor journal bearings are presented. Numerical comparative experiments for these models designed for turbocharger TKR-8.5S are made by application of the hydrodynamic prediction methodic for multi-film journal bearing. Prospects of application of the developed designs are proved.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):17-21
pages 17-21 views

The optimization of the turbine blade-disk interlock of the type “fir tree”

1 1., 1 1.

Abstract

The stiffness stress state in the interlock blade-disk of the type “fir tree” in the condition of crack birth is examined here. The changing of the stiffness of a stress state is considered in depending on the basic interlock angels. The approach for the interlock optimization provides the increase of the fracture strength.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):22-27
pages 22-27 views

Operate reliability enhancement of thermogenerator modules for heat engine with acoustic emission method

1 1.

Abstract

Methodology preparation of thermogenerator modules (TGM) selection for heat engine in backend of the assembly process with acoustic emission method is carried out. Acoustic emission (AE) method and its informative attributes are justified for TGM quality control. Special amplitude informative AE parameters were introduced for this purpose. There are also results of ТGМ longevity test with AE signals registration and selection method in this paper.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):28-34
pages 28-34 views

Ways of increase of efficiency of modern innovative manufacture

., .

Abstract

Article is devoted actual problems of increase of efficiency of the modern machine-building enterprise. Problems of perfection of preparation and retraining of personnel are discussed; preparations of manufacture on the basis of through use of modern information technologies, managements and the manufacture organizations on principles of reengineering of business processes, modernization of manufacture for introduction of the advanced technologies.
VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):35-39
pages 35-39 views

Increasing efficiency of pressurization of the rocket tanks in the flight

1 1., 1 1.

Abstract

In this paper it is shown the analysis of the onboard rocket tanks pressurization system functioning. The basic direction of the rocket tanks pressurization process are proposed.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):40-44
pages 40-44 views

Research of roughness of surface rollers with modified contact on the basis of analysis of thear autocorrelation functions

Nosov N.V., Abramov A.D., Haustov V.I.

Abstract

New approaches to estimation of a roughness of rollers’ surfaces after finishing processing are offered in the article. During research two methods were compared. The first method is traditional – researching the profile of the surfaces. The second is based on application of optical-electronic means and computer technologies. Results of comparison of a roughness of a surface after grindings by abrasive circles are presented.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):45-54
pages 45-54 views

the research of the influence of the maximal stress duration in the cycle of loading upon the low-cycle fatigue and the long-term strength of the turbine shaft made of the material ЭИ 961-Ш

1 1., 1 1., 1 1.

Abstract

The results of the experimental research of the interference influence of the cyclic and static failure rate on the low-cycle fatigue and long-term strength of the turbine shaft made of material ЭИ 961-Ш at the temperature of 5000C are examined here. The tests were carried out in the conditions of the cyclic, static and repeated static loading of the standard specimens and LPT shafts of a gas turbine.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):55-63
pages 55-63 views

The determination of the efficient parameters of surface strenghtening the thin-walled and the small-hard parts of gas turbine engines based on deformation tolerance

1 1., 1 1.

Abstract

The energetic method for determination of the efficient parameters of strengthening has been developed on the basis of the analysis of the residual stress of parts as well as on the initial stress conception. This method provides the increase of the endurance strength and the relationship of parts within the limits of technological tolerance. The realization of the method is described on the example of shot peening strengthening.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):64-69
pages 64-69 views

Methods calculation of fatigue crack growth period and her it’s graphic generalization

1 1., 1 1.

Abstract

As a principle we have used the limiteds diagrams of stress intensity factors and the Paris formula. Given methods allows quantitative to value residual longevity of the details with developing fatigue crack (creeping) and velocity of her its growing by means of kinetic diagram.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):70-79
pages 70-79 views

Research of methods for protection the surface of cryogenic tanks from ice formation

1 1., 1 1., 1 1.

Abstract

Process of formation of ice on walls of cryogenic tanks of carrier rockets is observed, theoretical calculation of weight of ice formed of the rain water which has got on a cold wall of a tank is carried out, experimental researches of process of formation of ice, and also protection methods cryogenic surfaces from ice formation are spent.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):80-84
pages 80-84 views

Алгоритм вибрационной диагностики кинематического узла механизма

1 1., 1 1.

Abstract

Изложен алгоритм вибродиагностики кинематического узла механизма, полученный в результате теоретического и экспериментального исследования прохождения возмущающего сигнала от узла механизма до его опор.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):85-92
pages 85-92 views

Probabilistic estimate of compressor blades durability to foreign object damage

1 1., 1 1.

Abstract

Foreign object damage is a significant cause of failure in gas turbine engines. The paper describes a methodology for probabilistic estimation of real compressor blades durability to foreign object damage. The methodology is based on numerical and experimental modeling of blade damage, experimental and computational procedure for assessment the fatigue strength loss of the damaged blades using minimum fatigue tests, failure probability calculation. The methodology may be used for evaluation the efficiency of durability rising procedures.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):93-97
pages 93-97 views

Using of heat-pipes with increased heat conduction as core elements of system of thermal control for aerospace equipment

., ., .

Abstract

This paper, executed under the direction of doctor of engineerings sciences, professor of Biryuka Vladimir Vasil'evicha, studies the main thermal physic characteristics of heat-pipes with increased heat conduction, which have axial grooves made of aluminum alloy AD31 as wick.
VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):98-101
pages 98-101 views

Way of increase in efficiency of cycle gas turbine units

1 1.

Abstract

The opportunity of increase in work and increase of effective efficiency of complex cycles is considered on the way increase in a degree of increase of pressure up to optimum on effective efficiency for a simple cycle under condition of ensuring of equality of effective efficiencies simple and complex cycles as criterion of efficiency of the last.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):102-108
pages 102-108 views

Features of designing gas turbine of complex cycle GT24

1 1.

Abstract

Features of designing gas turbine of a complex cycle with intermediate warm up GT24 and GT26 firms ABB on base gas turbine of simple cycle GT11N2 are considered.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):109-112
pages 109-112 views

Realization of the multichannel cnc machining methods

1 1., 1 1.

Abstract

This article describes the actual experience with the integrated CAD/CAM system for the development of control programs for the multi-channel CNC machining. Author describes the methods of channel synchronization during the simultaneous milling-lathing machining. Aspects of postprocessor development are shown on the example of threechannel machine tool.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):113-117
pages 113-117 views

Influence of impulse generation mode on electro-erosion treatment

1 1., 1 1., 1 1., 1 1.

Abstract

We consider a scheme of replacing the communication channel which is an active-inducing electric circuit having its load in inter-electrode space of active-volume character. Analysis of impulse values is carried out with the help of spectrum characteristics.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):118-121
pages 118-121 views

Inkjet heat transfer working model phone (fuel transportation) refrigerator drip emitters prospective spacecraft

1 1., 1 1., 1 1.

Abstract

Using the scheme of radiant heat transfer between the unbounded plane and rows of tubes in parallel planes, considered heat transfer inkjet linen cloths coolant moving in the longitudinal direction of die refrigerator drip emitters and ending in space. A design scheme of temperature changes during cooling jet linen cloths in space. We calculated the formula for determining the current and the average temperature along the length of linen cloths, as well as the length of linen cloths depending on the heat load from the Erase spacecraft. Using the proposed simple model of heat transfer inkjet linen cloths refrigerator drip emitters and space led to the practical coincidence of our calculations the number of drop of heat into outer space droplets refrigerator and the average temperature along the length of the jet with the results obtained using a complex model of heat transfer drop linen cloths Konyukhov G.V.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):122-131
pages 122-131 views

The comparative analysis of ways for manufacturing of forging pipes made from C17200 alloy for friction bearings for hard loaded parts

1 1., 1 1.

Abstract

The question of influence of forging technology on alloy C17200 microstructure and operational properties of pipe products in this article is considered. On the basis of the analysis of a microstructure the conclusions are drawn about primary mechanisms of plastic deformation in such processes as direct hot pressing and isothermal punching.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):132-137
pages 132-137 views

Decrease in toxicity of transport diesel engines by neutralisation nitrogen oxide of the fulfilled gases

1 q., 1 1.

Abstract

The basic toxic components of the fulfilled gases of engines are nitrogen oxide. One of the most perspective methods of decrease in toxicity of diesel engines is the method not catalytic reaction restoration NOx by ammonia. The design procedure of the constructive sizes of neutralizer taking into account features of diesel engines is developed.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):138-142
pages 138-142 views

Obliteration’s problems in capillary-porous structures of aerospace hydro systems’ parts

1 1., 1 1.

Abstract

This paper deals with a problem of locking (obliteration) in capillary structures and porous parts used in aerospase hydro systems. It is showh the results of this process’ computational modeling.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):143-146
pages 143-146 views

Optimization characteristics of rotor-support system from NK-14ST free power turbine with consider statics and dynamics propertys

1 1., 1 1.

Abstract

Issues of choosing supports for modernizing free power turbines, calculations and optimization of working characteristics of slide bearings are analyzed. The differential equations of rotor motion regarding its design features are presented. The results of the calculations of forced oscillations upon the system are shown and an analysis of the feasibility of improving the support of a free power turbine is given.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):147-156
pages 147-156 views

Effect of coagulation of drops on fuel spray characteristics behind atomizers

1 1., 1 1.

Abstract

Coagulation (fusion) of particles is one of the main reasons of dispersion evolution, which means mechanical mixture of environment (gaseous and liquid) with particles of disperse phase (solid or liquid). The phenomenon is observed in various physical situations: in solutions – Brownian coagulation, in rain drops formation process – gravitation coagulation in combustion chambers over atomizers – turbulent coagulation. The time evolution of particle size distribution due to Brownian and turbulent coagulation in combustion chambers was systematically investigated.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):157-161
pages 157-161 views

The mixing efficiency of liquid droplet fuel and air flow in the frontal swirl devices

1 1., 1 1.

Abstract

This work devoted to investigation of frontal swirl device for low-emission combustion chamber. It deals with the mixing processes of liquid droplet fuel and air flows. The numerical model includes the Reynolds equations and Lagrangian individual droplet equations. Fuel distribution calculations for any constructions of swirler were made. The results show the agreement coincident of experimental and calculation results.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):162-170
pages 162-170 views

Mixing parameters investigations and methods of approach to calculations and development of the thrusters with a spray-centrifugal scheme of NT and NDMH mixing on the confusion chamber wall in considered

1 1.

Abstract

Many years investigations results in field of mixing parameters studies in the thrusters developed CMDB named after A.M.Isaev are described. The NT and NDMH spray-centrifugal mixing scheme on the confusion chamber wall in considered.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):171-177
pages 171-177 views

Forecasting of the properties of structural materials and the choice of optimal technologies of their production

1 1., 1 1., 1 1., 1 1.

Abstract

The method of billets production by casting has been introduced. It allows controlling the composition and the structure of the billets’ material at the expense of variations of chemical structure, temperature regimes, as well as artificial mechanical and other impacts on the flux during crystallization processes. The interdependence between the produced structure and mechanical properties of the material has been researched.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):178-183
pages 178-183 views

Method of calculating of the load characteristics of cylindrical support with a discrete location of elastic damping elements of the MR material

1 1., 1 1., 1 1., 1 1., 1 1.

Abstract

The paper shows the method of calculation of static load characteristics of cylindrical support with discrete distribution of elastic damping elements made of pressed wire MR material. The method is based on the experimentally determined nonlinear material properties, operating in the free volume in its compression and on the generalized curves obtained during compression in a confined space.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):184-190
pages 184-190 views

Particularity of thermal condition computation oF LRE with cooling by liquid oxygen

1 1.

Abstract

In this article considered computation of thermal condition of new LRE with cooling by liquid oxygen. Substantiation of LRE cooling channel design is considered, analysis of various procedures of computation convection heat flux and heat transfer coefficient is performed. As the result distribution of chamber wall temperature (hot gas side) and coolant pressure is presented. Recommendations on lowering wall temperature and it measuring during fire tests is proposed.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):191-196
pages 191-196 views

About elaboration diagnostic methods of elements the pneumohydrosystem productions

1 1., 1 1., 1 1.

Abstract

This article describes the research work of influence of gas-filled "vessel-pipeline-valve" system element parameters on nature and quantitative indexes of initial pressure waves appeared after change of valve cross section. The mathematical model describing initiation of flow in the gas-filled pipeline during valve opening. The scheme of calculation of non-stationary movement of a nonviscous compressed liquid in the pipeline which area changes on time and longitudinal coordinate is offered.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):197-203
pages 197-203 views

Consideration of active forces at internal-combustion engine analysis in MSC.ADAMS environment

1 1., 1 1., 1 1.

Abstract

The dynamic analysis of internal-combustion engine in MSC.ADAMS environment requires calculation of piston applied gas pressure forces versus piston motion ratio. The analysis of indicator diagram is performed with KDAM code application depending upon piston diameter, compression ratio, pressure gain, advance angle. The dynamic analyses have been performed for in-line, V-type and opposed internal-combustion engines.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):204-209
pages 204-209 views

The interconnection between the benzo(a)pyrene and the soot emissions heat-engine using hydrocarbons fuels

1 1., 1 1., 1 1., 1 1.

Abstract

The benzo(a)pyrene absorption on the soot particles are viewed. The investigation is carryed out of the absorption properties carbons absorbents (activated carbon and soot) to benzo(a)pyrene and estimate the possible extraction. A hypothesis about difference of experimental data benzo(a)pyrene emissions by heat-engine was expressed.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):210-214
pages 210-214 views

The efficiency of aligning gratings at engine inlet of ground power plants

., .

Abstract

In this paper the results of cylindrical gratings application for decrease of air flow irregularity in engine intake are presented. The gratings have high efficiency and reliability. It is shown that the technical state of the gratings should be checked up.
VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):215-218
pages 215-218 views

The detecting improvement by laser surface sounding

1 1.

Abstract

The possibilities of method of laser location implementation with use of changeable wavelength, pulse frequency and pulse duration were investigated. For the present method dependence of characteristics of surface reflecting against laser wavelength, pulse frequency and pulse duration at the surface light sounding were expose. The changeable wavelength and tunable pulse-periodic operation of operation are unique possibilities of laser systems.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):219-226
pages 219-226 views

Current preventive control of a technical process on a basis of exponential smoothening

1 1.

Abstract

Algorythm of exponential smoothening of a time row having an arbitrary trend. This algorythm can be used at automated control of a technical process in real time conditions.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):227-230
pages 227-230 views

Dependence between microscopic characteristics of the material MR and parameters of press forming

1 1., 1 1.

Abstract

In the work approximation of a solid medium is developed for the description of the material MR. The relationship between structure elements (microscopic parameters x and σd) and macroscopic parameters of the whole model N and П. The “liquid drop model” of the material MR is constructed. The consecutive thermodynamic description of engineering process of the material MR manufacturing is offered. The dynamics of the material MR’s characteristics in engineering space are researched. The distribution function of pores along dimensions is got. The evident dependence of an average pore size of the material MR on compaction pressure is received. Good fit of theoretic and experimental data is got.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):231-236
pages 231-236 views

Feature of optimization of parameters of working process GTE with the free turbine at initial designing in the conditions of uncertainty

1 1., 1 1.

Abstract

Basic design of aircraft is characterized by uncertainty of GTE; multicriterion - uncertainty of purpose; uncertainty (predictive of) the source of design data and other project solutions in these circumstances can be to find areas of compromise. Given these characteristics of the area received good values for workflow small helicopter GTE.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):237-240
pages 237-240 views

Features of calculation of hydraulic characteristics of capillary spray jets of is liquid-stnyh rocket engines of small pull-rod

1 1., 1 1., 1 1.

Abstract

The method of calculation of hydraulic resistance of a liquid in capillary spray jets of liquid rocket engines of small pull-rod is developed at an isothermal current and with heat supply. Dependences for calculation of borders of the single-phase, not developed and developed superficial boiling of a liquid and heat exchange in the given areas of a current are offered.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):241-247
pages 241-247 views

Мethod of design calculation of centrifugal emulsive duplex fuel nozzle

1 1.

Abstract

Design calculation method of duplex centrifugal emulsion spray burner for arbitrary construction scheme is created. Expression for lumped geometric characteristic of emulsion spray burner which takes into consideration influence of viscous emulsion is received. It allows calculate all required parameters of designing emulsion spray burner with required in practice precision.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):248-252
pages 248-252 views

FMS-3000, programming amilling machine 6M13GN-1 a program controller

., ., ., .

Abstract

Essential elements of programming the process of machining parts of the knee-type milling machine, 6М13GN-1, with the help of numerical control machine-tool FMS-3000. There are varies programme examples for different parts formation, in particular, the programme of one definite part machining with the help of end millind cutter.
VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):253-260
pages 253-260 views

Mathematical model of small-thrust rocket engine with gaseous oxygen and hydrogen in pulse operation

1 1.

Abstract

Is indicated that working substance in combustion chamber corresponds a variable-mass and variable-composition body. Its variation is described with calculation equations for variable-mass and variable-composition body thermodynamics. System of equations for calculation combustion products equilibrium composition is composed. Mathematical model of small-thrust rocket engine which allows to determine ideal engines parameters for pulse mode is designed.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):261-267
pages 261-267 views

Calculation of the first resonant frequency and the first resonant factor of a sound absorption of material МR

1 1., 1 1., 1 1., 1 1.

Abstract

It is possible to express sound-proof property of material МR (MR) by the first resonant frequency (FRF) and by the first resonant factor of a sound absorption аg. In work the equation of calculation of the FRF of МR in function of cos, from which the graphic way receives the FRF is received. After comparison of values of the FRF treated as a result of the decision of the formula with values, received by a method of long lines, it is drawn a conclusion on greater accuracy of new method. Considering influence of attenuation of a resonance of pores, for coth yh the amendment is made. As a result of the decision of two equations are received the first resonant factor of a sound absorption аg. After comparison with the measured values аg, it is drawn a conclusion on accuracy of calculation information.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):268-273
pages 268-273 views

Influence of the frequency and load on wave deformation processes under high cycle fatigue

1 1., 1 1., 1 1., 1 1.

Abstract

Main and fatigue crack front in homogeneity under high cycle loading was considered. It was considered in the view of wave deformation process in metals. Represented rules on the basis of plane longitudinal section hypothesis allow using wave equations for crack structure description. This method of crack front differential analysis is the basis of cyclic strength wave theory.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):274-282
pages 274-282 views

Modeling of structure of the porous MR material in process of heat conduction

1 1.

Abstract

Principles of modeling of structure of MR material and heat conduction process for absence of convection of media in holes are presented in this article.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):283-288
pages 283-288 views

Modeling of heat conduction process in porous MR material

1 1.

Abstract

Principles of modeling of structure of MR material and heat conduction process for absence of convection of media in holes are presented in this article.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):289-293
pages 289-293 views

Productivity enhancement by modelling based ONMRPII/ERP systems

1 1., 1 1., 1 1.

Abstract

The issue describes is reflect the basic aspects of the managerial and economical modeling of industrial systems, as well as main methodologies of the business-process modeling. The article provides us with some data about existing program packages of the ERP level by the example of Microsoft Axapta. The analysis is conducted of capabilities of corporate information system (CIS) for modeling of different industrial enterprise processes, and the main trends of research in the sphere of integration of CIS into the business-process modeling are indicated in the issue.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):294-297
pages 294-297 views

Properties and structure of "trivalent" chromium coatings, deposited with nanoparticles of metal oxides

1 1., 1 1., 1 1., 1 1., 1 1.

Abstract

Physical-mechanical properties of chromium coatings, deposited from oxalic-sulphatic solution containing nanoparticles Al2O3 & ZrO2, are investigated. Results of accelerated corrosion test in the salt spray chamber by the cluster “trivalent” coatings with additional processing are represented. Structure & morphology of Cr(III)-coatings, deposited from solution containing nanoparticles Al2O3, are fixed by the methods of X-ray photoelectron & Auger electron spectroscopies (XPS & AES).

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):298-303
pages 298-303 views

PDM implementation efficiency in mechanical industry

1 1., 1 1., 1 1.

Abstract

This publication is based on the methods of the calculation of efficiency of the preproduction phase of manufacturing process. Authors assume that manufacturer has an early stage of the PDM(Product Data Management) implementation and compare results of ENOVIA SmarTeam with mechanical industry market feedbacks.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):304-310
pages 304-310 views

The flowing reactor as the tool of an experimental research of processes of transformation self-igniting liquid rocket fuel

1 1., 1 1.

Abstract

The method of the flowing reactor for experimental issledo-vanija processes of transformation self-igniting liquid rocket fuel is offered and approved. The given method allows to investigate initial stages of processes of transformation of fuel and a fashion-lirovat influence on them of various boundary conditions, first of all influences is effectivesti mixtures in a liquid phase of components.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):311-315
pages 311-315 views

Research of laws of interaction of components in a liquid phase self-igniting liquid rocket fuel

1 1., 1 1.

Abstract

Experimental results of processes of interaction of components in a liquid phase of self-igniting liquid rocket fuel are presented. The data on sizes of time of an induction of reactions in a liquid phase and to temperatures of liquid and gas intermediate products is obtained. Sizes of completeness of transformation and degree of gasification of fuel at the given stage of transformation of fuel and influence on them of completeness of mixture of components in a liquid phase and time of stay of intermediate products are defined.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):316-321
pages 316-321 views

Researching error of blade locating in mechanism the POMKL–BLIK fixture by the system of approximate analysis of double-dimensional densities of probability

1 1., 1 1., 1 1., 1 1.

Abstract

The article is devoted to basing error research in blade fixturing mechanism setup of POMKL-BLIK device. The research is divided on two extended phases. The first experimental phase is carrying out to determine dispersion field by measuring etalon spatial locations with coordinate measuring machine. The processing of data obtained while experiment was executed on the second phase. The problem is in double-dimensional data spreading. Therefore the method of double-dimensional probability densities approximation was given in the article. The result of the experiment would be analytical expression of double-dimensional statistical law that describes random field of experimental points and probability fiducial intervals in double-dimensional space.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):322-327
pages 322-327 views

The analyze of work of throttle cooling system’s microheat exchanger, wich uses nitrogen with nearly critical parameters

1 1., 1 1., 1 1., 1 1.

Abstract

This paper deals with the work of throttle cooling system with standard tank and the work of throttle cooling system with cryogenic tank. It is done comparison of geometric and hydraulic characteristics micro heat exchangers both systems. It is shown a prospect of application of throttle cooling system with cryogenic tank for cooling of IRreceivers used in aerospace navigation and exploration systems.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):328-334
pages 328-334 views

Pulsing chambers of combustion and their application in aerospace engineering

1 1., 1 1., 1 1.

Abstract

In article necessity of creation of air-rocket engine for perspective flying machines is shown and application in it of the chamber of combustion is proved. The current review of pulsing chambers wich are probably to apply in the space technics, the models is designed and tested by authors. The scheme of the combined engine with the direct-flow chamber of pulsing and a perpendicular supply of gas stream is developed. Fire tests of bench model of a power-plant are conducted and basic taktiko-technical characteristics are received.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):335-343
pages 335-343 views

Application’s ways of gas–turbine power plants of NK-family for upgrading of heat electric generation plant

1 1., 1 1., 1 1., 1 1.

Abstract

In this paper deals with actual questions and possible upgrading ways of heat electric generation plant with power and economy gas-turbine power plants of NK-family. It is also shown that gas-vapor devices are able to increase working power and efficiency of heat electric generation plants with minor investment outlays. This action allows to work on energy market in summer time and also during decreased heat consumption period.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):344-351
pages 344-351 views

Research of the wet condition in fuel tanks of high weight booster rockets during storage and aviation transportation periods

1 1., 1 1., 1 1.

Abstract

In this paper, executed with participation of doctor of engineerings sciences, professor of Biryuka Vladimir Vasil'evicha, there are experimental research data of wet condition in fuel tanks of high weight booster rockets for providing corrosion protection during storage and aviation transportation periods.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):352-359
pages 352-359 views

Development and study of the designs of sprayers with increased speed for internal combustion engine (ice)

., ., .

Abstract

In the article proposed constructive solutions of sprayers of different types for ICE, which are able to increase their speed, quality of the propellant atomization, control capability and also some other indices.
VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):360-364
pages 360-364 views

The calculated study of fluid structure in a hub an axial aviation turbine

1 1., 1 1.

Abstract

The paper conducts comparison of gas torrent patterns in interblade channels of a turbine stage. Received in calculation by means of CFX program with the existent physical conceptions and experimental data. The calculated torrent structure matches well the given data, and allows to study secondary torrents in an axial turbine channel in detail.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):365-368
pages 365-368 views

The story of invention and development of supercharge units of internal combustion engines

1 1., 1 1., 1 1.

Abstract

The paper examines the story of creation and development of supercharge sets of internal combustion engines. The main stages and directions of their development are disclosed in the paper, the main preconditions and limitations, which predetermined the way of development of supercharge sets.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):369-376
pages 369-376 views

Working out of methods preporation of execution technological audit for rearmament innovation factory

., ., .

Abstract

In article considered problems of absence of techniques of execution technological audit for rearmament innovation machine-building factory, the basic business processes of the modernized manufacture are described, recommendations to technological preproduction of operating manufacture are developed, advantages of rearmament factory with preliminary procedure of technological audit are shown.
VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):377-381
pages 377-381 views

Mathematical modelling and parametric research of flow of the twisted turbulent single-component stream of the propulsive mass in the trance- and supersonic areas of Laval nozzles

1 1., 1 1.

Abstract

With use of mathematical model of the space (twisted) viscous (turbulent) flow of a single-component propulsive mass in a trans-and supersonic areas on the basis of system of the equations of Nave-Stokes and the software of computer systems ANSYS CFX and STAR-CD CD-adapco, distribution of gasdynamic properties in Laval nozzles is gained and some regularity of such type of flows is determined.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):382-391
pages 382-391 views

Methodology complex of hardware-in-the-loop functional modelling of gas turbines and its systems

1 1., 1 1., 1 1., 1 1., 1 1.

Abstract

The problems of building of adequate structural complex gas turbine model for hardware-in-the-loop investigation of the automatic control system behavior with system faults are discussed. The structure and technology for creation of the adequate complex gas turbine model with an example of twin-shaft bypass reheat turbo jet for hardware-in-the-loop simulation, including a special complex of models of switching between operation and reconfiguration in FADEC control-and-condition-monitoring systems with system faults are offered.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):392-400
pages 392-400 views

Study of gradient rotor speed and support dissipation coefficient influence to supercritical rotor characteristic

Ivanov A.V.

Abstract

Rotor is one of the main parts of high speed rotating machine. This article dedicated to some questions of rotor critical frequencies overcoming speed and damping influence to rotor dynamical characteristics and seals operability.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(3-2):28-32
pages 28-32 views

This website uses cookies

You consent to our cookies if you continue to use our website.

About Cookies