Vol 11, No 5-1 (2012): Special Issue

Cover Page

Full Issue

Stabilization of steady motions of a single rotor gyrostat with a cavity filled with a liquid of high viscosity

Alekseev A.V., Bezglasny S.P., Krasnikov V.S.

Abstract

The present paper investigates the motion of the mass center-rotor gyrostat with a cavity completely filled with a viscous liquid. Are given the dynamic equations of motion in angular rate on the axis of the body of the carrier-related coordinate system.The conditions of stability and instability of motion in the first approximation. For unstable regimes of motion is synthesized by active stabilizing control by the feedback principle.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):13-18
pages 13-18 views

Drag function for the striking element arrow-class on subsonic velocity

Ganziy Y.V., Salakhov M.M., Mitiukov N.W., Busygina E.L.

Abstract

The work is devoted to the definition of drag coefficient model submunitions on the example of the arrow. In a medium of ANSYS CFX been calculated and compared with experimental data published.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):19-21
pages 19-21 views

Gas-discharge generation of near-wall flows

Ivchenko A.V., Zhuravliov O.A., Shakhov V.G.

Abstract

The paper presents results of gas jets study generated by surface discharges in air at atmospheric pressure applied to the problems of flows control. The possibility of large eddies destruction by near-wall jet is shown. For modification of boundary layer by surface discharge, the electrode system configurations are discussed.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):22-31
pages 22-31 views

Experimental study of air flow in axisymmetric diffuser output section with rotating wall

Kurkin E.I., Ivchenko A.V.

Abstract

The effect of axisymmetric diffuser wall rotation was experimental studied. Diffuser with an apex angle of 30 degrees was investigated by PIV method on Re number from 9 000 to 44 000 and the angular velocity from 0 to 3000 rpm. POD method was used for no stationary flow description. The study showed that rotating diffuser walls leads to expansion of the air flow at the output, and can be viewed as a method to increase their effectiveness.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):32-37
pages 32-37 views

Lift of the airfoil with spoiler

Redkina K.V., Frolov V.A.

Abstract

A model of a stationary vortex for the potential circulation flow around airfoil-spoiler combination has been proposed. The solution is obtained for the flow of incompressible ideal fluid. The Complex Variable Function Theory is applied. For the simulation of the recirculation area, a stationary vortex is used, the location of which is found by minimizing a velocity function. Dependence of the lift on the angle of attack, relative length of the spoiler and its angle of deflection is obtained.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):38-42
pages 38-42 views

Drag function for the striking element sphere-class on subsonic velocity

Romanenko I.V., Crawford K.R., Mitiukov N.W., Busygina E.L.

Abstract

The work is devoted to the definition of drag coefficient model submunitions on the example of the sphere. In a medium of ANSYS CFX been calculated and compared with experimental data published.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):43-45
pages 43-45 views

Numerical study of free convection in long vertical cylinder at constant vertical gradient of temperature on lateral surface

Khoroshev A.S.

Abstract

Buoyancy-induced flow of water in the long vertical cylinder is studied. CFD (Computational Fluid Dynamics) tools (Ansys CFX) is used. Influence of aspect ratio and difference of temperatures on wall of the cylinder on intensity of buoyancy-induced flow is analysed.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):46-48
pages 46-48 views

Increase of operational characteristics of details at the expense of depositions plasma thermal spray coatings cluster structure

Dokukina I.A.

Abstract

Creating the structure of ordered clusters of plasma coating enhances performance properties of coatings. This structure facilitates the localization of fatigue cracks and prevent their further spread. The simulation of the formation of such a structure, which allows to determine the optimal modes of deposition of different materials.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):49-54
pages 49-54 views

Methods of calculating the parameters of the topology and routes for manufacturing operations in the aggregate-assemblu production

Grechnikov F.V., Tlustenko S.F.

Abstract

The features of geometric dimension of linking the elements of assembly of compounds based on a unified information model of the product. It is shown that when establishing tolerances for each of the links dimensional chain of fundamental importance that the ratio between actual design and technological constraints dimensional element of the assembly determines the level of residual stresses in the product design, resulting in the assembly process, and should be considered in computer-aided design technology processes.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):55-61
pages 55-61 views

Complex automation of process planing and numeric control of mechanical processing of hulls details

Khrustitskiy K.V., Cherepashkov A.A.

Abstract

In article is discussed development of the complex system computer aided design adaptive technological processes and numeric control of the mechanical processing of the details of the transport machines.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):62-66
pages 62-66 views

Optimization of strength characteristics of lighting devices aircraft by construction of virtual models

Abulkhanov S.R., Goryainov D.S., Skuratov D.L.

Abstract

We study the possibility of building a digital model of the aircraft lighting unit diffuser surface, being an authentic reproduction of the real headlight diffuser, using the state-of-the-art modeling tools. The authentic numerical model means that not only the geometric parameters but also physiotechnical properties are in the maximal possible agreement with the real object. The use of the authentic 3D model in various CAD-systems will not only enable the real object’s performance parameters to be prognosticated but also its design to be optimized based on a variety of criteria.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):67-72
pages 67-72 views

Thin-walled plates and covers with surface-crack defects in elastoplastic approach

Astafiev V.I., Yakovlev A.S.

Abstract

In work definition of area of possible limiting conditions of thin-walled plates and covers from an ideal elastoplastic material with not through blind fractured defect (scratch) is considered. Areas of possible limiting conditions for scratches of variable depth are considered. Comparison of experimental and theoretical data is given. The problem of determination of the limiting extent of defects which at the set level of operational loadings can lead to catastrophic destruction of all design is solved.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):73-78
pages 73-78 views

Design procedure of factor of rigidity of aviation elastic elements

Barmanov I.S.

Abstract

In work the design procedure of factor of rigidity of an elastic element of type of "the squirrel wheel» is resulted. The given technique allows to raise essentially accuracy of calculations of the elastic elements applied in aviation engines.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):79-83
pages 79-83 views

Evaluation procedure of effect of surface treatment on low-cycle material fatigue

Bukhanko A.A., Kotcherov E.P., Ovchinnikova S.A.

Abstract

The plastic flow near the angular wedge under the burnishing of surface is considered. Fields of strain and specific internal forces work in the plastic region are specified. An algorithm for determination of part of internal forces work is suggested. This part of work has connected with the material hardening and has effect on thefailure of material under the burnishing.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):84-88
pages 84-88 views

Nitriding influence on residual stresses and endurance limit of specimens with notches made of 38Х2МЮА steel

Vakuljuk V.S., Chirkov A.V., Bukatyi A.S., Philippov A.A.

Abstract

The residual stresses after nitriding in specimens with notch made of 38Х2МЮА steel are studied. It is established that the average integral residual stresses criterion can be used for the evaluation of endurance limit increment at bending for such specimens.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):89-94
pages 89-94 views

Residual stresses and endurance strength in the specimens with V-shaped notches made of ВНС40 steel

Kirpichev V.A., Saushkin M.N., Sazanov V.P., Semyonova O.Y.

Abstract

Residual stresses in cylindrical specimens made of BHC40 steel with V-shaped notches after grinding, notching, nitriding and nitriding with the subsequent thermoexposition at 600°С during two and 590 hours are studied.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):95-99
pages 95-99 views

Fatigue strength prediction of surface - hardened cylindrical specimens of different diameters

Kirpichev V.A., Pavlov V.F., Chirkov A.V., Ivanova A.V.

Abstract

On the example of specimens made of steel 20 of different diameters experimentally
established, that the utilization is more rightful for of surface hardening influence on endurance
limit under stress concentration.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):100-107
pages 100-107 views

The solution of an uncoupled thermoelastic problem with a displacement vector and a heat flow defined on a body boundary

Makarova I.S.

Abstract

In this paper the method of the solution of an uncoupled thermo elastic problem with boundary conditions of the first kind is offered. The analytical decision for homogeneous isotropic arbitrary form body limited to a piecewise smooth surface is found.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):108-112
pages 108-112 views

Evaluation of thermochemical treatment influence on fatigue strength of specimens under normal and high temperatures

Pavlov V.F., Vakuljuk V.S., Afanasieva O.S., Bukatyi A.S.

Abstract

The influence of cementation, nitriding and borating on endurance limit of corset specimens made of ВКС-5, ЭП718 and ВНС-17 allows under normal and high temperatures are studied. It is established that the average integral residual stresses criterion can be used for the prediction of endurance limit for specimens like these.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):113-119
pages 113-119 views

Research of notch radius and depth influence on residual stresses distribution character in the smallest cross-section of surface hardened detail

Sazanov V.P., Larionova Y.S.

Abstract

Notch radius and depth influence on axial residual stresses in the smallest cross-section for surface hardened cylindrical parts of different diameters is studied using FEM modeling.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):120-123
pages 120-123 views

Simulation of aircraft multistage axial turbine working processes taking into account over-shroud leakage flows and blading inflows

Baturin O.V., Popov G.M., Kolmakova D.A.

Abstract

The calculation research of the working process of multistage axial turbine in two different software systems was performed. The calculations were performed using an identical geometry, boundary conditions and under the same engine operation conditions. Detailed information about the parameters and structure of the flow in the turbine.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):124-130
pages 124-130 views

Reduction of circumferential variation in the final stage of IPC

Baturin O.V., Krivcov A.V., Matveev V.N., Popov G.M.

Abstract

Circumferential variation of the flow in final stage rotor wheel, caused by the support racks at the exit of the IPC, is evaluated by means of intermediate pressure compressor’s workflow 3D model. The methods of reducing the flow circumferential variation by changing final stage’s guide vanes angles.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):131-137
pages 131-137 views

Vortical gaz-wind-energy plant

Biryuk V.V., Zubrilin I.A., Krasnorutskiy A.S.

Abstract

The estimation of possibility of use combined vorticalvind-energy plants for development of the electric power. The three-dimensional model is designed and numerical calculation stator parts vind-energy plant is executed. Distributions of parameters of a stream in all settlement area are received. Dependence of power efficiency of installation on static pressure on an exit from calculation area is revealed.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):138-142
pages 138-142 views

Construction and calculation of three-dimensional model threedimensional model of ice combustion chamber for dynamic calculation of heat processes in ANSYS Fluent

Biryuk V.V., Gorshkalev A.A., Kayukov S.S., Uglanov D.A.

Abstract

This paper deals with building of model combustion chamber of a four-cycle four-cylinder internal combustion engine Mitsubishi 4G63. 3D-model is done in program complexes SolidWorks and ANSYS Gambit. In ANSYS Gambit interfaces is created for the volumes belonging to the model. Then model is exported to ANSYS Fluent for dynamic calculations of work processes of Internal Combustion Engine. Also it is shown results of this calculation.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):143-148
pages 143-148 views

Approaches to modeling work of gas turbine engine`s core as a connected task

Krivcov A.V., Shabliy L.S., Baturin O.V.

Abstract

Various approaches for simulation of gas turbine engine core operating by means of CFD software are presented. Their main advantages and disadvantages are described.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):149-154
pages 149-154 views

Investigation of relative geometric parameters influence on bypass engine mass

Kuzmichev V.S., Krupenich I.N., Kulagin V.V., Miheeva E.S., Nikolaev A.A.

Abstract

Influence of relative diameters of bypass engine turbocompressor on its mass is described.
VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):155-159
pages 155-159 views

Methods and means of aircraft gas turbine engine conceptual design underlying the CAE system «ASTRA»

Kuzmichev V.S., Tkachenko A.Y., Rybakov V.N., Krupenich I.N., Kulagin V.V.

Abstract

Main underlying principles of the CAE-system «ASTRA» are described.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):160-164
pages 160-164 views

Problem formulation of bypass engine parameters optimization with a preselected gas generator

Kuzmichev V.S., Kulagin V.V., Tkachenko A.Y., Krupenich I.N., Rybakov V.N.

Abstract

Formulation of problem bypass engine parameters optimization using the aircraft efficiency criteria in a case of gas-generator being preselected is described.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):165-169
pages 165-169 views

Influence of the initial design data uncertainty on the choice of optimal working process parameters of gas turbine engine

Kuzmichev V.S., Tkachenko A.Y., Rybakov V.N., Krupenich I.N., Kulagin V.V.

Abstract

Influence of the initial design data uncertainty on the choice of optimal working process parameters of gas turbine engine is described.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):170-176
pages 170-176 views

Optimization of design diffuser of GTE combustion chamber with using CAE-systems

Orlov M.Y., Matveev S.S., Zinkovskiy V.S.

Abstract

When using computer technology design of diffuser combustion chambers GTE specific problems arise, solutions are considered in this paper.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):177-183
pages 177-183 views

Investigation of effects of multistage compressor final stage blading shape on compressor performance and flow pattern

Popov G.M., Krivcov A.V., Kolmakova D.A.

Abstract

The influence of rotor blades with anti-vibration shroud and Shvarov's profile compared to conventional blades on compressor efficiency is investigated. The variation of compressor efficiency is quantitatively evaluated at 4 operation modes.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):184-190
pages 184-190 views

Optimization of aircraft seven stage compressor first stages parameters

Popov G.M., Matveev V.N., Baturin O.V., Kolmakova D.A.

Abstract

The optimization of multistage compressor of gas turbine engine is considered. Optimization was performed by changing the guide vanes angles of three stages. As a result the increasing of compressor efficiency by 0.3% was achieved on one of the main modes of operation.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):191-198
pages 191-198 views

Dependence of required turbine inlet temperature at cruise mode of long-term flight on bypass ratio

Rybakov V.N.

Abstract

The relation between turbine inlet temperature at flight cruise mode (at specified thrust value) and the bypass ratio is described. It is proved that the increase of the bypass ratio leads to increase of gas temperature value.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):199-202
pages 199-202 views

Use of the dynamic programming method for solving tasks of GTE management optimization using the aircraft efficiency criteria

Tkachenko A.Y., Kuzmichev V.S.

Abstract

Constraint-driven method of GTE management optimization based on aircraft efficiency criteria is described. The method is based on dynamic programming and minimax principle of optimality for objective function.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):203-207
pages 203-207 views

Automatization of creation vane models for CAE with PROFILER

Shabliy L.S., Dmitrieva I.B., Popov G.M.

Abstract

Methodology of automotive creation of vane 3D-model for gas-dynamic analysis in NUMECA is seeing. Ways of solving different problems during this process is suggested.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):208-214
pages 208-214 views

Natural development of forming structure and properties of forgeable AL-ZN-MG-CU alloys having different content of main alloying elements, microadditives and impurities

Vakhromov R.O., Antipov V.V., Tkachenko E.A.

Abstract

The complex studies have been made to investigate the influence of the main alloying elements Zn, Mg, Cu, small additives Zr, Sc, Ag, impurities Fe and Si on the strength, fracture toughness, fatigue properties, corrosion resistance, microstructure parameters (dispersoids, strengthening precipitates, recrystallization degree, grain size) of forged semiproducts manufactured from high strength forgeable alloys of Al-Zn-Mg-Cu system.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):215-222
pages 215-222 views

Computer simulation of forming operations of the magnetic-pulse processing of metals

Grechnikov F.V., Chernikov D.G.

Abstract

This paper presents the results of computer simulation of magnetic-pulse processing of metals using a new electromagnetic module of the multi-purpose finite element software LS-DYNA.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):223-227
pages 223-227 views

Determination of parameters of pulse-magnetic forming

Karpuhin V.F.

Abstract

The paper proposes the engineer method for calculation of forming of a wide spectrum of axially symmetric and sheet articles. Therewith such important factors of the process are taken into account as the energy losses by inducing a field within the inductor in the case of forming on a workpiece expansion scheme and presence of inductor's turns not covered by the workpiece. The experimental verification has supported rather high accuracy of determination of regimes of forming of different articles.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):228-232
pages 228-232 views

Action of pulsed magnetic field on the melt in the manufacture of "metal-nonmetal" composites

Lazareva A.A.

Abstract

In this paper the results of exploratory researches in the Samara State Aerospace University, to obtain of the “metal-nonmetal” compounds with the action of pulsed magnetic field (PMF) in the molten metal are considered. Two types of such compounds are obtained: 1) metal electrical contact plugsin the carbon blocks, and 2) a composite material based on aluminum matrix reinforced with carbon fabric.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):233-238
pages 233-238 views

The choice of the kinematic scheme of formoobrazovany by stretch forming of obvodoobrazuyushchy covers of the difficult spatial form

Miheev V.A., Klochkov Y.S., Kuzina A.A., Grechnikova A.F., Savin D.V.

Abstract

The choice of the kinematic scheme of formoobrazovany by stretch forming of obvodoobrazuyushchy covers of a difficult spatial form depends on the angular values connected with a corner of coverage of an obtyazhny punch by preparation and with a corner of unbendingof a cover between operations of consecutive covering.Researches were carried out by means of the final and element analysis in the program ANSYS/LS-DYNA environment for a cover with concrete geometrical characteristics. By results of research the choice of one of three kinematic schemes was carried out.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):239-245
pages 239-245 views

Modelling of the sequential positive sequential scheme of formoobrazovany by stretch forming of obvodoobrazuyushchy covers of double curvature of the minimum nonuniform thickness

Miheev V.A., Klochkov Y.S., Kuzina A.A., Grechnikova A.F., Savin D.V.

Abstract

Existing ways ofstretch forming aren't capable to ensure obvodoobrazuyushchy covers of double curvature of the minimum nonuniform thickness. However use of the flexible device of mathematical modeling of surfaces of planes and coverings will allow to execute all necessary calculations and to offer the consecutive scheme combining two operations of covering with intermediate unloading and unbendingby received on the first covering of a cover of the demanded geometrical form.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):246-252
pages 246-252 views

Increasing process efficiency in the production of casting parts of aircraft engines by the action of pulsed magnetic field on the melt

Chernikov D.G., Glouschenkov V.A., Igolkin A.J., Nikitin K.V., Akishin S.A.

Abstract

This article presents the results of comprehensive research of the influence of the pulse magnetic field of high intensity on the process of crystallization, structure, foundry and mechanical properties of Al-Si alloy castings.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):253-257
pages 253-257 views

Probable consequences of Russia’s accession to world trade organization for national aviation industry

Kolpakov S.K., Kutzobin A.P.

Abstract

The article gives the analysis of World Trade Organization documents with the aimo festimation of probable consequences of Russia’s accession to this international organization for national aviation industry. Three groups of documents were under consideration – multi lateral greements, dispute cases materials and Russia’s accession documents. It was found that government support of aviation industry does not completely correspond to WTO legislation. It is advisably to work out new methods of civilair craft development financing using the experience and materials of WTO disputes of civil aircraft producers.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):258-265
pages 258-265 views

Development of automated systems LC UPD

Blyumenshteyn A.A., Chernikov M.S., Zheleznov O.V.

Abstract

Scientific Research Center of CALS-technologies has developed an automated system lifecycle management UPD, which allows organizing the ordering process, design and assembly of UPD.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):266-271
pages 266-271 views

Development of classifier of plane’s parts for the solution of taks of automated CNC programs prepairing for CNC machines

Gismetulin A.R., Sergeev O.S.

Abstract

The article tells about the way of editing recognition and machining rules for new features. Also here are researches of the most efficient ways of using CNC machine’s options.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):272-276
pages 272-276 views

Developing models of information-analytical monitoring system design, engineering and manufacturing processes aircraft companies

Zheleznov O.V., Blyumenshteyn A.A., Chernikov M.S.

Abstract

The article considers the prospects of using information-analytical system for monitoring the status of design, technology and manufacturing processes of the aircraft enterprise. Also, there are proposals to implement the functional modules of IAS and developed a model and methodology for its implementation.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):277-283
pages 277-283 views

Modern approach for design management in production enterprise integrated information space

Ivaschenko A.V., Kremenetskaya M.E., Filatov A.N., Peisakhovich D.G.

Abstract

The paper describes an approach for production enterprise staff interaction management in processes of designengineering technology of aerospace techniques in integrated information space based on a methodology of top-down design. There is provided an analysis of practical implementation of top-down design methodology in Samara Space Center. To implement the top-down design methodology there is proposed a structure for conditional management of new technique design workflow.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):284-292
pages 284-292 views

Methodological aspects of estimation foundry design and technology process efficiency for aircraft companies

Levkina O.Y.

Abstract

We propose an approach of estimating foundry efficiency in aircraft building company. The approach is based on level determination of the goal achievement in foundry. Besides, it allows to provide an objective assessment of the production in terms of resource consumption, to reveal factors that have a significant impact on the manufacturing process, to search for production reserves, to determine the feasibility study of new forms of production management and organization.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):293-297
pages 293-297 views

Basic approaches and requirements to the formation of polyplatform integrated automated system of aircraft life cycle support based on the product electronic definition

Nazarov V.V., Shabalkin D.Y., Polyanskov Y.V.

Abstract

The approaches to the continuous information lifecycle support system construction are investigated. Systems mentioned should be based on poly-platform information systems integration.Comparison of mono-platform and polyplatform solution from the applicability is presented. Necessary conditions for autonomic system integration are shown. Model of construction integrated information lifecycle system is suggested.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):298-305
pages 298-305 views

Computer-aided design of programs for CAM-systems based on the use of intelligent pattern mechanical processing of standard elements

Popovich A.V., Levschanov V.V., Lisov K.A., Chavkin E.M.

Abstract

Intelligent system for modern CAM to create NC-programs.The main points related to the processing of feature elements in modern CAM-systems. We describe how to implement neural network algorithms to create the CNC program. Showed a new way of building in automatic selection of cutting tools and machining strategies.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):306-310
pages 306-310 views

The interactive system for collecting data of technical condition of aircraft components

Blagorazumov A.K., Kirpichev I.G.

Abstract

The paper presents an Internet-based system developed to collect data of technical condition of aircraft components from aircraft operators that do not use information systems with the ability to export the data.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):311-317
pages 311-317 views

Information system of normative requirement management in airline for prevention of accidents

Dyatlov A.Y., Zaykin M.A., Kondratyeva A.S., Gorbunov I.V.

Abstract

Normative requirement management in airlines is one of the ways of flight safety ensuring. The article suggests an approach to the creation of requirement management information system.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):318-322
pages 318-322 views

Automation of inspection supervision in tasks of registration of aircraft airworthiness certificates

Petrov D.V., Kirpichev I.G.

Abstract

The question of automation registration and control certificates of airworthiness of the aircraft by means of information-analytical system for monitoring aircraft airworthiness.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):323-327
pages 323-327 views

Fuzzy optimization of the passenger airlines network based on the hubs airports system

Romanenko V.A.

Abstract

The problem of search of optimum structure of the in-Russian airlines network formed based on hub airports system is considered. Criterion of optimality is the passenger transportation cost price minimum. Fuzzy numbers sets the volume of passenger traffic between pairs the airports. The structure of the hub airports set is certain.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):328-334
pages 328-334 views

Organization of go-ahead engineers training for aircraft industry at the example of the strategic alliance of Ulyanovsk state university and CJSS “Aviastar-SP”

Polyanskov Y.V., Shabalkin D.Y., Evseev A.N.

Abstract

Realization of the efficient personnel training model is presented. Recent social and economic factors have been taken into consideration. The main directions of the strategic alliance of Ulyanovsk State University and CJSS “Aviastar-SP” are shown.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):335-341
pages 335-341 views

Experience of the deployment the CAD-complex at the educational virtual enterprise

Cherepashkov A.A., Bukatin A.V.

Abstract

In article are discussed the methodology of training personnel to the Computer Aided Design skills. Are offered the general principles of the creation EVE on platform ASKON for standard supply at technical universities.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2012;11(5-1):342-345
pages 342-345 views

This website uses cookies

You consent to our cookies if you continue to use our website.

About Cookies