Vol 8, No 2 (2009)

Cover Page

Full Issue

AIRCRAFT AND SPACE ROCKET ENGINEERING

Flight path of a supersonic aeroplane as the first stage of an aerospace system

Balakin V.L., Potapov V.I.

Abstract

The paper analyses the motion of a supersonic aeroplane as the first stage of an aerospace system when performing the “dynamic zoom” manoeuvre with the aim of maximum climb at a given slope of the flight path.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):7-13
pages 7-13 views

Developing an electronic reference book on thermogasodynamic properties of rocket engine fuel combustion products taking into account non-ideal character of the working process

Silyutin M.V.

Abstract

The paper shows the expediency of developing an electronic reference book on thermogasodynamic properties of rocket engine combustion products taking into consideration the non-ideal character of the working process. The description of the physico-mathematical model used and the algorithm of numerical solution of the model’s equations are given. The results of the approbation of the reference book developed are outlined. Its possibilities as applied to the improvement of the existing small thrust liquid-propellant rocket engines (STLPRE) as well as for developing liquid-propellant rocket engines and gas-turbine engines using promising fuel components are analysed.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):14-23
pages 14-23 views

Dependence of the extent to which the space vehicle’s own atmosphere and plasma generated by stationary plasma engines affect the space vehicle on its structural lay-out

Testoyedov N.A., Smirnov V.A.

Abstract

The paper describes the mechanisms of influence of the space vehicle’s own atmosphere (OA) and plasma generated by stationary plasma engines (SPE) on the space vehicle. The results of investigating the extent to which these factors depend on the structural layout (SLO) of the space vehicle are given. Ways of minimizing the negative effect of OA and plasma generated by SPE at the stage of choosing the space vehicle’s SLO are planned.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):24-32
pages 24-32 views

MECHANICAL ENGINEERING AND POWER ENGINEERING

Analysis of temperature separation efficiency in vortex gas flows

Biryuk V.V., Kurnosov N.Y., Tarnopolsky A.V.

Abstract

The paper presents the results of experimental research and a semiempirical procedure of the design of separating vortex tubes. The procedure is arranged taking into account the hypothesis of vortex interaction in whirled gas flows.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):33-41
pages 33-41 views

Optimization of material distribution in load-bearing units for several cases of loading

Boldyrev A.V.

Abstract

A definition of the most rigid construction for several cases of loading is given and an algorithm of its search is developed. A hybrid method of optimization is proposed which combines the algorithm mentioned and the concept of the full stress level. High accuracy of the hybrid method is demonstrated using numerical examples.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):42-51
pages 42-51 views

Rotor blade compressor working process analysis

Dovgyallo A.I., Kolomin I.V.

Abstract

The paper presents the analysis of the rotor blade compressor (RBC) working process. The main characteristics of the working process are defined on the basis of the accepted structural parameters. The use of RBC is shown to be promising for the compressor unit of the microcryogenic cooling system of infra-red imaging equipment.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):52-60
pages 52-60 views

Quality of sheet articles forged by polyurethane in the open volume

Yefimov N.A., Yefimov Y.A.

Abstract

The paper shows the efficiency of blanking sheet articles by polyurethane using open and semi open methods. The results of numerical and experimental analysis of these processes are given. The influence of non-uniform unit load of a polyurethane tool on the plane ness of the articles forged is shown. An efficient forging technology and technological recommendations are developed.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):61-67
pages 61-67 views

Computer simulation of thin-walled tube sink drawing

Kargin V.R., Kargin B.V., Pastushenko T.S., Yerisov Y.A.

Abstract

The paper presents the results of computer simulation of the process of thin-walled tube sink drawing into conic dies using the finite element method in a specialized software complex DEFORM-2D.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):68-74
pages 68-74 views

Development and analysis of compressed bending process in a die with an elastic punch

Komarov A.D., Yeskina Y.V., Ponikarova N.Y.

Abstract

A die design has been developed for compressed bending of sheet articles and cutting blanks off a strip in one stroke of the press. The die provides increased thickness of material in the bending area, reduction of the radius of bending and spring back, which improves the strength, rigidity, quality and life of the articles as well as labour productivity. The procedure for calculating the basic parameters of article production process is given. The die design has been patented.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):75-81
pages 75-81 views

Friction control on changing parameters of friction pairs using sequential feeders

Rybaltchenko D.Y., Bystrov N.D.

Abstract

Comparative analysis of functional possibilities of sequential lubrication systems with the control of a given period of lubrication material renewal and changing parameters of the lubricated friction pairs is carried out. Calculation tables are given that are used when designing a sequential lubrication system with a liquid lubricant, a SEHY-P 400/400 hard table taken as an example. The main conditions of the operation of a lubrication system with lubrication control on changing parameters of friction pairs on the basis of a pumping device with programmable lubricant feeding is considered.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):82-92
pages 82-92 views

Criteria for selecting categories of efficiency of soundproof materials used for car noise reduction

Fesina M.I., Krasnov A.V.

Abstract

The paper justifies objective criteria for selecting brands of soundproof materials based on the classification ranging of their soundproof properties. One hundred and forty brands of soundproof materials made by 32 manufacturers have been analysed. Information on the values of "soundproof capacity" parameter as well as on categories of the acoustic quality of some brands of materials analysed is given.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):93-103
pages 93-103 views

ELECTRONICS, MEASURING EQUIPMENT, RADIO ENGINEERING AND COMMUNICATION

Analysis of determinate error of an optoelectronic angular shift sensor on multicomponent optronic structures

Stepanov M.V., Matyunin S.A.

Abstract

The paper presents the analysis of a determinate error of an optoelectronic angular shift sensor on multicomponent optronic structures on the basis of the sensitivity theory propositions.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):104-109
pages 104-109 views

CONTROL, COMPUTER SCIENCE AND INFORMATION SCIENCE

Multichannel television method of object geometrical parameter remote measurement

Zhiganov I.Y.

Abstract

The paper deals with the theoretical foundations of television devices for measuring geometrical parameters of complex objects using several telecameras spaced apart at a fixed distance. The procedure of measuring on the basis of automatic calibration and the processing algorithms ensuring the independence of measurement results on the distance from the object and its displacement in space are given.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):110-114
pages 110-114 views

Algorithms and devices for input signal identification in problems of dynamic object control and diagnostics

Zasov V.A., Tarabardin M.A., Nikonorov Y.N.

Abstract

The paper deals with the problem of separation of individual signals from the additive mixture of several signals, i. e. the problem of signal identification. Two groups of algorithms for solving the problem are analysed: those based on the knowledge of channel properties and the knowledge of signal source properties. The results of modeling the algorithms under consideration are given as applied to the problem of controlling data transmission rail channels widely used in railway transport.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):115-123
pages 115-123 views

Process of autoreengineering of entreprise common information space

Ivashchenko A.V.

Abstract

The paper describes an approach to organizing common information space of an enterprise as an open selforganizing system. It is based on the construction of a design-production model. A design-production model and sources of disturbances registration of which makes it possible to organize autoreengineering of the enterprise common information space are described.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):124-134
pages 124-134 views

Defining parameters of a linear dynamic system multidimensional at the input and output given autororrelated signal interference

Karpov A.A., Katsyuba O.A.

Abstract

The paper deals with the theory and method of solving the problem of consistent evaluation of multidimensional linear difference equation parameters with autocorrelated interference in input and output signals on the basis of least square method generalization (as the most common in conditions of a priori uncertainty). The consistency of the obtained estimates of unknown true parameter values is proved.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):135-142
pages 135-142 views

Reliability indicators of information control systems with hardware and software failures as complex time functions

Maryukhnenko V.S.

Abstract

A complex form of presenting reliability indicators of non-recoverable information control systems with hardware and software failures is proposed on the axiomatic basis. Complex forms of intensity, probability of survival and failure of complex systems without redundancy and with replacement redundancy are dealt with.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):143-149
pages 143-149 views

Statistical modeling of the process of serving the leaving passengers at the international Kurumotch airport

Romanenko V.A.

Abstract

The task of optimizing the parameters of the system of serving leaving passengers at the check-in stage in the airport building has been solved by using the method of statistical modeling. Time characteristics of the check-in stage and the capacity of the check-in system which minimize time losses and provide the proper level of comfort for passengers have been determined. Detailed stochastic portraits of passenger service system functioning for the actual conditions of operation of the International Kurumotch airport (Samara) have been obtained.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):150-162
pages 150-162 views

Method of fault detection and diagnosis in linear stochastic systems in the process of filtration

Tsyganova Y.V.

Abstract

A computationally efficient method of fault detection and its identification in the class of linear stochastic control systems in the process of filtration has been obtained. The efficiency of the method lies in the fact that a decision is taken on a limited set of likelihood function values, the values being computed directly in terms of values generated by the filter.

VESTNIK of Samara University. Aerospace and Mechanical Engineering. 2009;8(2):163-171
pages 163-171 views

This website uses cookies

You consent to our cookies if you continue to use our website.

About Cookies